Guide · Tankless water heaters
What to know before a tankless water heater installation
Updated Nov 16, 2026 · 8 minute read · By the Home Water Finder team
Last reviewed: November 16, 2026, America/Denver (MT)
A tankless (on-demand) water heater heats water as it flows, rather than storing it in a tank. Installation is not a generic “swap the tank” job. It can involve gas-line sizing, venting, electrical service, water-quality treatment, and local permits. Manufacturer instructions are model-specific.
Rinnai’s *N Series Residential Condensing Installation and Operation Manual*, which we opened for this draft, states that installation and service must be performed by a trained and qualified professional, service agency, or the gas supplier, and that improper installation can void the warranty. Treat that as a minimum bar, and use the manual for the exact brand and model being installed.
When you are ready to hire, find tankless water heater installers. That national category page follows the same “guide plus directory entry” pattern as /water-softeners/ and may be drafted later. You contact the company directly. A listing is not an endorsement, and we do not sell leads. For tank-style replacement, use water heaters.
This page is not a do-it-yourself gas, vent, or electrical guide.
In short
- Hire a trained, qualified professional. Check the license at the official state board (plumbing, mechanical, or the class your state requires for this work).
- Ask the installer to follow the model’s installation manual and local codes, including gas supply, venting, combustion air, clearances, and condensate handling on condensing units.
- Hard water and scale matter. The Rinnai manual we reviewed says that in areas known to have hard water or scale build-up, the water must be treated, and that replacement of components due to water-quality damage is not covered by the warranty. Your model’s manual may use different wording — read it.
- Get a written, itemized estimate. Angi (updated Aug 3, 2026) lists tankless *installation* at $1,404–$3,903, with an average of $2,641. Labor is listed separately at $600–$1,850. See the cost section. Those are Angi figures, not an HWF average.
What “qualified” means in practice
The Rinnai manual tells the installer that a trained and qualified professional should have attended a product-service training for the installation, and lists skills that include gas sizing; connecting gas and water lines; installing venting through a wall or roof; and training in tankless installation. It also says proper installation is that professional’s responsibility, and that the manual should be left with the water heater when the job is done.
Your state may require a specific contractor license. In Arizona, for example, plumbing work is described under official ROC classifications such as R-37 / CR-37; look up the company at the Arizona ROC contractor search and read license classifications rather than guessing. Other states have their own boards (Texas uses the Texas State Board of Plumbing Examiners, for example). Use the board where the work will be done.
What the installer should walk through with you
Use this as a conversation list, not as a substitute for the manual or the code:
- Fuel and electrical. Gas type (natural gas or propane), pipe sizing, and any electrical requirements for the model. The Rinnai manual includes a dedicated section on connecting the gas supply and, for some jurisdictions, additional state gas regulations.
- Venting and combustion air. Condensing and non-condensing units have different vent materials and routes. The manual we reviewed includes a full venting section and warns that surrounding air used for combustion must be free of compounds that corrode internal parts.
- Location and clearances. Indoor vs outdoor ratings, freeze risk, and service access.
- Water quality and scale. If your water is hard, ask whether pretreatment is required for warranty or performance. A softener or scale-control device, if recommended, should appear in the written scope so you are not comparing unlike bids. See how water softeners work if hardness is also on your list.
- Permits and inspection. Local rules, not a national yes/no.
- Startup and owner orientation. How to set temperature, what maintenance looks like, and who to call for warranty service.
If you smell gas, follow the appliance’s warning label and the gas supplier’s instructions; do not use this article as an emergency procedure.
What published cost studies say
Home Water Finder has not independently surveyed installers and does not publish its own average. The figures below are from Angi, “How Much Does a Tankless Water Heater Cost? [2026 Data],” updated Aug 3, 2026, and fetched on November 16, 2026 (America/Denver). We did not use Department of Energy dollar figures this pass: Angi attributes annual energy-cost savings to DOE, but the energy.gov tankless page we tried returned HTTP 404.
| Item | Angi figure | What it covers |
|---|---|---|
| Installation | $1,404–$3,903; average $2,641; smaller electric units as low as $380 | Angi labels the $1,404–$3,903 band as installation cost (unit and setup). The $2,641 figure is that page’s overall average. The $380 floor is a small electric unit, not a whole-house gas job. Fuller comparison, including HomeGuide, is on tankless water heaters. |
| Unit itself | About $200–$2,000 | Equipment, separate from labor |
| Install materials | About $130–$280, plus about $10 per linear foot for piping and insulation | Materials, not labor |
| Labor | $600–$1,850, around three hours; plumbers $45–$200 per hour | Labor only |
| Electric installation | $800–$1,500 | Angi's electric-installation band, typically the lower-complexity job (no combustion vent) |
| Natural gas installation | $1,000–$1,500, plus about $200 a year to run | Installation plus Angi's operating figure |
| Propane installation | $1,000–$1,500, about $350 a year to run | Installation plus operating figure |
| Solar | $1,800–$5,700 | Installing a tankless solar water heater |
| Add-ons | Angi lists $200–$500 as a combined band for permits, electrical-service upgrades, and old-heater removal in one summary; the body separately lists removal at $500 or more, gas-line work up to $1,000, and an electrician at $50–$100 per hour. | Different Angi sentences, different scopes — do not merge them into one add-on number. These extras are what usually push a conversion above a simple swap. |
City permit fees belong on that city’s published schedule; Angi does not replace it. Required water treatment, if any, should appear as a line item on the quote (see water softener installation cost if a softener is in scope). Compare complete written estimates for the same model family and the same plumbing, gas, and vent work.
Sourced facts
| Fact | Source | Date |
|---|---|---|
| Installation and service must be performed by a trained and qualified professional, service agency, or the gas supplier; improper installation may void the warranty | Rinnai N Series Residential Condensing Installation and Operation Manual (PDF) | Fetched Nov 16, 2026 |
| In areas known to have hard water or scale build-up, the water must be treated; water-quality damage is not covered by that warranty language | Same Rinnai manual | Same |
| Water supplied to the unit must be potable and free of corrosive chemicals, sand, dirt, or other contaminants; the professional is responsible for checking this (wording in that manual) | Same Rinnai manual | Same |
| Arizona plumbing and related license classifications are defined by the Registrar of Contractors | ROC license classifications; contractor search | Retrieved Nov 16, 2026 |
| Installed, labor, and add-on ranges in the cost section | Angi tankless 2026 page | Accessed Nov 16, 2026, America/Denver (MT) |
Other brands (Rheem, A.O. Smith, Navien, Noritz, and others) publish their own manuals. Use the manual that matches the model on the quote. A Rheem Eagle tankless use-and-care PDF URL returned HTTP 200 when checked this turn, but this draft quotes the Rinnai manual we fully extracted.
FAQ
Can I install a tankless water heater myself? Not according to the Rinnai manual we reviewed, which requires a trained and qualified professional, service agency, or the gas supplier. Your model and your local code may be equally strict. This guide does not provide DIY steps.
Does hard water affect a tankless unit? It can. The Rinnai manual we opened says that in known hard-water or scale areas the water must be treated, and that water-quality damage is not covered under that warranty language. Ask the installer what your water test or CCR implies for the model they are quoting.
How much does tankless installation cost? Home Water Finder does not publish its own average. Angi (updated Aug 3, 2026) lists installation at $1,404–$3,903, with a $2,641 average, and labor at $600–$1,850. Gas-line work, electrical upgrades, and old-unit removal can add more; Angi states those add-ons in more than one range, so read the cost table rather than combining them. Compare itemized installed quotes that include venting, gas or electrical work, and any pretreatment.
Is a tankless unit always a better choice than a tank? Not automatically. Fuel type, incoming water temperature, simultaneous demand, venting path, and water quality all matter. This page does not rank products.
Where can I find an installer? Tankless water heaters on Home Water Finder. That category page is the directory entry for the installer term. This guide stays on the informational question. For tank-style replacement, see water heaters.
Sources
- Rinnai, N Series Residential Condensing Installation and Operation Manual, https://media.rinnai.us/salsify_asset/s-c368fed3-6728-4e35-b4be-13c0c6384595/100000467-N%20Series%20Residential%20Condensing%20Installation%20and%20Operation%20Manual.pdf
- Arizona Registrar of Contractors, license classifications, https://roc.az.gov/license-classifications
- Arizona Registrar of Contractors, contractor search, https://azroc.my.site.com/AZRoc/s/contractor-search
- U.S. Geological Survey, “Hardness of Water,” https://www.usgs.gov/water-science-school/science/hardness-water (for hardness classes if you are also evaluating pretreatment)
- Angi, “How Much Does a Tankless Water Heater Cost? [2026 Data],” updated Aug 3, 2026, https://www.angi.com/articles/how-much-does-tankless-water-heater-cost.htm — accessed November 16, 2026, America/Denver (MT)
Cost sources
Master log: cost sources.
| Figure | URL | Accessed | Covers |
|---|---|---|---|
| Angi installation $1,404–$3,903; average $2,641; unit ~$200–$2,000; materials ~$130–$280 plus ~$10/ft; labor $600–$1,850; plumber $45–$200/hr; fuel-type installation and operating figures; summary add-ons $200–$500; removal $500 or more; gas line up to $1,000; electrician $50–$100/hr | https://www.angi.com/articles/how-much-does-tankless-water-heater-cost.htm | Nov 16, 2026, America/Denver (MT) | Mix of installation totals, equipment, labor, and add-ons as Angi labels them. DOE savings dollars were not used (source URL 404). |
Find installers near you
You call them directly. We never ask for your phone number.